HM Metal-Housed Heating Mantles with Built-in Controllers

HM Metal-Housed Beaker Heating Mantles with Built-in Controllers - BriskHeat

BriskHeat HM Metal-Housed Heating Mantles are fiberglass insulated round bottom flask heaters for laboratory and pilot laboratory applications. They are used to heat a variety of round bottom shaped vessels, to either increase temperature or keep media at a constant process temperature. All heating mantles are manufactured to high quality standards of craftsmanship.

The exterior of the HM Metal-Housed Heating Mantle with Built-in Controller is a plastic-coated metal casing, with a pre-molded fiberglass liner to hold the round-bottom flasks. The heating element consists of a chrome-nickel alloy resistance wire which is electrically insulated using a crocheted high-temperature yarn. The adapted shape ensures an even heat transition to the glass flask, and a layer of fiberglass insulation under the heating element reduces heat dissipation to increase efficiency.

Flexible fiberglass heating element for uniform heat
Durable plastic-coated chemical resistant metal housing
Thermally insulated and grounded for safety
Round Bottom Flask Heater

NOTE: HCLAMP Rod Support Attachment Sold Separately

Round bottom flasks up to 20 liters (20,000ml)
Includes predrilled threaded hole on rear for clamp accessory
Built-in 1 or 2 zone heating option
120V or 240V
5-foot (1.5m) power cord

120V includes standard 3-prong plug (NEMA 5-15)
240V crimped ferrule terminated leads

For operating temperatures up to 450°C (842°F)

PRIOR TO INSTALLATION

Check for suspected damage to the heater like rips, punctures, etc.
Confirm voltage / wattage rating of heater is appropriate for power supply device or temperature controller. The heater is designed to work at a specific voltage to heat properly. Failure to operate the heater at the specified rating could result in overheating of the heating element, the surface being over-heated, or personal injury. Also note lower-than-rated voltage will result in under-heating.

To Avoid Electrical Shock, Always:

Use an electrical outlet that operates with a fuse or a circuit breaker and a ground fault circuit interrupt (GFCI).
Disconnect the mantle from the power supply prior to maintenance and servicing.

To Avoid Personal Injury:

Do not use in the presence of flammable or combustible materials. Fire or explosion may result. This device contains components which may ignite such materials.
Do not operate in damp or wet locations.
Refer servicing to qualified personnel only.
Flasks and vessels should be handled with care. Appropriate safety clothing, glasses, gloves, and coats should be worn when operating all heating mantles.

To Avoid Damage:

Never plug HM-MH models directly into a power source. Your heating mantle MUST be operated with a temperature controller and with an appropriate size flask, filled with fluid.
Never operate heating mantle without fluid within the flask.
Fluid should not be allowed to come in contact with the cavity of the heating mantle.
Never operate the mantle at temperatures above maximum exposure temperature .

INSTALLATION
Your heating mantle is a fiberglass-insulated heater designed for heating laboratory vessels. The mantles are specifically designed for glass flasks, however, with appropriate temperature control and product type, metal or plastic flasks can be used. Only use round bottom flasks of the size corresponding to the mantle size.

Install heating mantle around properly sized flasks.
For proper temperature control, secure the thermocouple, RTD, or other sensing device vertically along the lead wire seam of the blanket with one strip of adhesive tape so that it is sandwiched firmly in-between the heater and glass flask.
Sensor must be in close proximity to the heater to prevent overheating.
Sensor should be connected in accordance with instructions provided with temperature controller.
Ensure heater is in contact with the surface to be heated. The heater must fit tightly around the glass flask. Minimal air gaps between the heater and the flask provide the best thermal transfer of heat to the flask and extend heater life.
Once the mantle has been properly installed:
120VAC: Plug the heater into an acceptable temperature controller. Use a variable transformer, manual control, or automatic controller to prevent overheating.

Note: Due to their overall size, the heating mantle sizes 50ml and 100ml are only designed with one heating zone. They are put into operation by means of an MIN/MAX switch. Maximum heating element temperature for series HM-MC: 842°F (450°C).

Connect the heater to an appropriate power supply.
Heating Mantle can be switched on and off by using the green ON/OFF switch.
With the MIN/MAX switch the heating zones can be switched (See Figure 2)
The built-in power controller is used for the continuous adjustment of the power input.
The yellow indicator light indicates the heating power is on.
In case of the liquid level dropping during operation, adjust/switch heating zones accordingly.

Series HM-MC Metal-Housed Heating Mantles - heating zones

BAKE-OUT PROCEDURE FOR NEW HEATING MANTLES
On the initial heat-up of the mantles, a slight odor may be detected and some discoloration will
occur in the cavity area. The discoloration of the cavity area has no effect on the operation of the
mantle. If the heated vessel becomes discolored, it can be cleaned with water. To bake-out your
mantle prior to use, connect the mantle to your temperature controller and fill a flask
corresponding to the size of the mantle half full of water. Place the flask in the mantle cavity and
allow the water to come to a boil and continue boiling for approximately 15 minutes. The mantle
can be operated at full rated voltage during bake-out.

For more information, please see the complete manual: HM-Hard-Side-Heating-Mantle-Instruction-Manual.pdf

Configuration Options
NOTE: Selecting Configuration Options limit / refine the available products; to match your selection criteria.

1. Size

2. Voltage

3. Wattage

Available Options: HM Metal-Housed Heating Mantles with Built-in Controllers

Quantity	Price	UOM	Part Number	Type	Size	Voltage	Wattage
	$361.00	EA	HM0050MC1	Simple Product	50 ml	120	60
	$361.00	EA	HM0050MC2	Simple Product	50 ml	240	60
Out of stock	$410.00	EA	HM01000MC2	Simple Product	1000 ml	240	325
	$365.00	EA	HM0100MC1	Simple Product	100 ml	120	110
	$365.00	EA	HM0100MC2	Simple Product	100 ml	240	110
Out of stock	$484.00	EA	HM02000MC2	Simple Product	2000 ml	240	545
	$371.00	EA	HM0250MC1	Simple Product	250 ml	120	165
	$371.00	EA	HM0250MC2	Simple Product	250 ml	240	165
Out of stock	$682.00	EA	HM04000MC2	Simple Product	4000 ml	240	815
	$394.00	EA	HM0500MC1	Simple Product	500 ml	120	220
	$394.00	EA	HM0500MC2	Simple Product	500 ml	240	220
Out of stock	$818.00	EA	HM06000MC2	Simple Product	6000 ml	240	1090
	$410.00	EA	HM1000MC1	Simple Product	1000 ml	120	325
	$484.00	EA	HM2000MC1	Simple Product	2000 ml	120	545
	$526.00	EA	HM3000MC1	Simple Product	3000 ml	120	650
	$682.00	EA	HM4000MC1	Simple Product	4000 ml	120	815
	$818.00	EA	HM6000MC1	Simple Product	6000 ml	120	1090

NOTE: Selecting Configuration Options limit / refine the available products; to match your selection criteria.

Accessories

HCLAMP Support clamp for laboratory frame rods

Support clamp for laboratory frame rods
(Accommodates up to a 13mm diameter rod)

Learn more

Don't see your size or option? Have a question about which BriskHeat product is right for you? Need Application assistance? Contact Us. We are here to help!