Product Highlights Temperatures up to 400oF (204oC)
Power remains constant regardless of temperature Can be cut-to-length at job site Ideal for a wide range of general purpose applications - Mid-range process temperature control for food and chemical processing
- Water lines
- Fire protection systems
- Fuel oil
- Condensate return
- Hot water lines
- Lines periodically purged with 250 psig steam
Specifications- Maximum exposure temperature is 400oF (204oC)
- Moisture, chemical, flame, and radiation resistant
- 12AWG bus wires
- Dimensions 0.2" x 0.3" (5 x 8mm)
- 40 lb. (18kg) per 500-foot (152m) spool
TEFLON® is a registered Trademark of DuPont used under license. Approvals
Ordinary Locations
Hazardous Location (T3 rated):
Class I Division 2 Groups B, C, D
Class II Division 2 Groups F, G
Class III Division 2   Ordinary locations (120 and 240VAC only)  
Approval valid only when used with appropriate heating cable and installation accessories, and installed in accordance with all applicable instructions, codes, and regulations. Maximum Circuit Length in ft (m) | Cable | 120VAC | 208VAC | 240VAC | 277VAC | 480VAC | 3 watts / ft
(10 watts / m) | 360
(110) | 625
(191) | 720
(220) | N/A | 1440
(439) | 5 watts / ft
(16 watts / m) | 275
(84) | 477
(145) | 550
(168) | N/A | 1100
(335) | 8 watts / ft
(26 watts / m) | 220
(67) | 381
(116) | 440
(134) | 508
(155) | 880
(268) | 12 watts / ft
(39 watts / m) | 180
(55) | 312
(95) | 360
(110) | 416
(127) | 720
(220) |
Circuit Module Length in ft (m) | Cable | 120VAC | 208VAC | 240VAC | 277VAC | 480VAC | 3 watts / ft
(10 watts / m) | 2.0
(0.6) | 4.0
(1.2) | 4.0
(1.2) | N/A | 8.0
(2.4) | 5 watts / ft
(16 watts / m) | 2.0
(0.6) | 4.0
(1.2) | 3.0
(0.9) | N/A | 6.0
(1.8) | 8 watts / ft
(26 watts / m) | 2.0
(0.6) | 4.0
(1.2) | 4.0
(1.2) | 4.0
(1.2) | 6.0
(1.8) | 12 watts / ft
(39 watts / m) | 2.0
(0.6) | 6.0
(1.8) | 360
(110) | 4.0
(1.2) | 4.0
(1.2) |
Note: when ordering, please allow a minimum of 1 module length extra for terminations.  FE General Purpose Constant-Wattage Heating Cable Specification Sheet
Ordering InformationPart Number Matrix 
Connection / Termination Kits | Part Number | Kit | Enough to Complete | | FECABUC | Universal Connection / Termination Kit | Two end terminations and one input connection, or one power input splice. Note: Requires a double hub junction box. | | FECABKC | Lead / End Seal Kit | Five lead and end terminations. | | FECABSK | Splice Kit | One in line splice or one tee splice. Note: Requires pipe standoff, pipe straps, single hub junction box, and RTV sealant. | | FECABLP | Lead Termination Kit | One lead termination. | | FECABEP | End Termination Kit | One end termination. |
FE Connection / Termination Kit Specification Sheet Temperature Controller A temperature controller is required for this product. Check out temperature controller section for a complete selection of temperature controllers. Accesories | Adhesive Tape Helps to isolate the cable from the insulation and provides intimate contact with surface to be heated. | Part Number | Description | | PSAT36 | Pressure Sensitive Fiberglass Adhesive Tape
0.5" x 108' (13mm x 38m)
Temperature limit: 350oF (176oC) |
AAT260
AAT2180 | Aluminum Adhesive Tape
2" x 180' (51mm x 55m) / Temperature limit: 350oF (176oC)
2" x 180' (51mm x 55m) / Temperature limit: 550oF (288oC) |
|
 | Caution Label Required by code for every 100ft (3m) of pipe. | Part Number | Description | | BCLCAB | Electrical heat trace warning label. Required by code for every 10ft (3m) of pipe. |
|
 | Heat Conductive Putty Used to fill voids between cable and pipe surface. | Part Number | Description |
HCP1
HCP3 | Heat Conductive Putty. Used to fill voids between cable and pipe surface.
1 lb. (0.5kg)
3 lb. (1.4kg) |
|
 | Monitor Light Kit Provides a continuity check at the termination end of a cable circuit. | Part Number | Description | | MLK1001 | Single hub; 120VAC | | MLK2001 | Single hub; 240VAC | | MLK1002 | Double hub; 120VAC | | MLK2002 | Double hub; 240VAC | | MLBCAB001 | 120VAC replacement bulb | | 40180 | 240VAC replacement bulb |
|
 | Pipe Reducer | Part Number | Description | | BPRCAB010 | Adapts 0.75" NPT male to 1" NPT female |
|
 | Pipe Standoff Cast aluminum fitting. | Part Number | Description | | PSOCAB010 | 1.00" thread | | PSOCAB075 | 0.75" thread |
|
 | Pipe Strap Stainless steel pipe straps used to secure pipe standoff to pipe. | Part Number | Description | | BPSCAB2-6 | Stainless steel pipe straps used to secure pipe standoff to pipe.
Adjustable from 2" to 6" (51 x 152mm) |
|
 | RTV Sealant Silicone sealant used to seal lead pouches, end pouches, and pipe standoffs. | Part Number | Description | | RTV3.0 | Silicon sealant used to seal lead pouches, end pouches, and pipe standoffs. 3 oz. (89ml) |
|
SupportDocuments |
